{"product_id":"pressure-washer-14l-min-2500-psi-380v-4kw","title":"Pressure Washer, 14L\/min, 2500 Psi, 380V 4kW, Electric","description":"\u003cp\u003e\u003cmeta charset=\"utf-8\"\u003e\u003cspan\u003eA 4.0kW high-pressure washer.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eSpecifications:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003ePower:\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e4.0kW\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eVoltage:\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e380V Three phase\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eRevolutions:\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e1450RPM\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eMax. Pressure:\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e175 bar\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eFlow:\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e14.0 L\/min\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eUsage:\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe machine must be switched off when not in use. If the gun is released and the pump enters its unloading state, the machine can only facilitate this for 30 seconds before the water starts overheating and ultimately damaging the pump. If any damage comes to the pump from deformation or destruction of internal components, overheating is the likely cause.\u003c\/span\u003e\u003cbr\u003e\u003cbr\u003e\u003cspan\u003eThe machine comes with a \u003c\/span\u003e\u003ca href=\"https:\/\/www.semca.co.za\/product\/product.php?p=11131R\"\u003eRed Gun\u003c\/a\u003e\u003cspan\u003e, a 7m 280bar high-pressure hose, a short hose, a low-pressure chemical injector, and the following nozzles:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.semca.co.za\/product\/product.php?p=11139R\"\u003eRed nozzle\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.semca.co.za\/product\/product.php?p=11139Y\"\u003eYellow nozzle\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.semca.co.za\/product\/product.php?p=11139W\"\u003eWhite nozzle\u003c\/a\u003e\u003c\/li\u003e\n\u003cli\u003e\u003ca href=\"https:\/\/www.semca.co.za\/product\/product.php?p=11139K\"\u003eBlack nozzle\u003c\/a\u003e\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch1\u003eWARNING\u003c\/h1\u003e\n\u003ch2\u003e\"MUST DO\"\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eAll electrical conductors MUST BE PROTECTED against the water jet.\u003c\/li\u003e\n\u003cli\u003eThe appliance MUST ONLY BE CONNECTED to a correct earthed power supply.\u003cbr\u003eTIP: Use of Safety Residual Current Circuit-breaker(r.c.c.b) will provide additional protection for the operator(30mA).\u003c\/li\u003e\n\u003cli\u003eThe high pressure jet may cause loose particles to be propelled at high speed, therefor protective clothing and safety glasses MUST BE WORN.\u003c\/li\u003e\n\u003cli\u003eBefore carrying out any work on the cleaner, DISCONNECT the plug from the electrical supply socket.\u003c\/li\u003e\n\u003cli\u003eBefore pressing the trigger, GRIP the gun firmly to counteract the recoil.\u003c\/li\u003e\n\u003cli\u003eMaintenance and repair of electrical components MUST be done by a qualified staff.\u003c\/li\u003e\n\u003cli\u003eDISCHARGE residual pressure before disconnecting the high pressure hose.\u003c\/li\u003e\n\u003cli\u003eBefore using the appliance, CHECK every time that the screws are fully tightened and that there are no broken or worn parts.\u003c\/li\u003e\n\u003cli\u003eOnly use detergents which will not corrode the coating materials of the machine and it's parts. DO NOT USE bleach, alcohol, petrol, hydrochloric acid etc. as the solvents that are flammable and erodable.\u003c\/li\u003e\n\u003cli\u003eThe appliance operates at fluid pressures and velocities high enough to penetrate human and animal flesh, which could result is amputation or serious injury. DO NOT TREAT FLUID INJECTIONS AS A SAMPLE CUT! SEE DOCTOR IMMEDIATELY!\u003c\/li\u003e\n\u003cli\u003eOnly use chemicals desighed for pressure washer using mild soaps and chemicals compatible with aluminium and brass parts of the pressure washer.\u003c\/li\u003e\n\u003cli\u003eThe machine uses normal temperature and the temperature for the inlet should not be used with the temperature of 0°C or under 0°C.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003e\"MUST NOT DO\"\u003c\/h2\u003e\n\u003cul\u003e\n\u003cli\u003eDo not use the appliance with inflammable or toxic liquid, or any products which are not compatible with the correct operation of the cleaner.\u003c\/li\u003e\n\u003cli\u003eDo not use the appliance within range of persons unless protective clothing are worn.\u003c\/li\u003e\n\u003cli\u003eDo not use the appliance if supply cord or important parts of the appliance are damaged, e.g. safety devices, high pressure hoses, trigger gun.\u003c\/li\u003e\n\u003cli\u003eDo not direct the water jet towards people, animals, electrical equipment or the machine itself.\u003c\/li\u003e\n\u003cli\u003eDo not use the appliance outdoors in case of rain.\u003c\/li\u003e\n\u003cli\u003eDo not allow children or unprofessional staff to use the machine.\u003c\/li\u003e\n\u003cli\u003eDo not though the plug or socket with wet hands.\u003c\/li\u003e\n\u003cli\u003eDo not use the appliance if electrical cord is damaged.\u003c\/li\u003e\n\u003cli\u003eDo not use the appliance if the high pressure hose is damaged.\u003c\/li\u003e\n\u003cli\u003eDo not jam the trigger in the operating position.\u003c\/li\u003e\n\u003cli\u003eDo not with or alter the calibration of the safety valve.\u003c\/li\u003e\n\u003cli\u003eDo not alter the original diameter of the spray nozzle.\u003c\/li\u003e\n\u003cli\u003eDo not leave the appliance unattended.\u003c\/li\u003e\n\u003cli\u003eDo not move the appliance by pulling the electrical cord.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch1\u003ePUMP OPERATING FEATURES\u003c\/h1\u003e\n\u003cp\u003e\u003cspan\u003ePlease check each part according to the packing list when opening the carton, to check whether the parts are complete and in good condition. Keep all documents and manuals.\u003c\/span\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003ch2\u003eCHANGE OIL INLET PLUG\u003c\/h2\u003e\n\u003cp\u003eThe red plug on the pump is specially designed for transportation, before using the unit, please replace the red plug with the yellow plug or the brass plug in the spare parts package.\u003c\/p\u003e\n\u003ch2\u003ePRESSURE REGULATOR\u003c\/h2\u003e\n\u003cp\u003eThe pressure setting is preset at the factory to achieve optimum pressure and cleaning. If need to lower the pressure, the following methods can be used:\u003c\/p\u003e\n\u003col\u003e\n\u003col\u003e\n\u003cli\u003e\n\u003cb\u003eBack away from the surface to be cleaned.\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003eThe further away the user is, the less pressure is on the surface to be cleaned.\u003cbr\u003eDO NOT try to increase pump pressure, a higher pressure setting may damage the pump.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eChange to the 40° white nozzle.\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003eThis nozzle delivers a less powerful stream of water and a wider spray pattern.\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eAdjust the pressure regulator on the pump.\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003eTurn the pressure regulator knob anti-clockwise to lower the pressure. Once you have finished using your pressure washer, return the pressure regulator to it's original position by turning it clockwise.\u003cbr\u003eDO NOT try to turn pressure regulator knob past the build-in stop line otherwise damage to the pump may be resulted.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003c\/ol\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch2\u003eTYPE OF NOZZLE\u003c\/h2\u003e\n\u003cp\u003eYour unit is equipped with four spray nozzles. Each nozzle is colour coded, and delivers a specific spray pattern for a particular cleaning purpose.\u003c\/p\u003e\n\u003col\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cb\u003eRed:\u003c\/b\u003e\u003cspan\u003e \u003c\/span\u003e0° nozzle\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eYellow:\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e15° nozzle\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eWhite:\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003e40° nozzle\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eBlack:\u003cspan\u003e \u003c\/span\u003e\u003c\/b\u003eChemical nozzle\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cbr\u003e\u003cspan\u003e\u003cb\u003eCAUTION\u003c\/b\u003e\u003c\/span\u003e\u003cbr\u003e\u003c\/p\u003e\n\u003col\u003e\n\u003cli\u003eThis high pressure spray from your unit is capable of causing damage to surfaces suck as wood, glass, automobile paint, auto striping and trim, and delicate objects such as flowers and shrubs. Before spraying, check the item to be cleaned to assure yourself that it is strong enough to resist damage from the force of the spray.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch2\u003eCHANGING NOZZLES\u003c\/h2\u003e\n\u003cp\u003eDO NOT attempt to change the nozzle while the unit is running.\u003cbr\u003eTurn the engine or gun OFF before changing the nozzle.\u003c\/p\u003e\n\u003col\u003e\n\u003col\u003e\n\u003cli\u003ePull quick-release back and insert nozzle.\u003c\/li\u003e\n\u003cli\u003eRelease quick-release and\u003cb\u003e\u003cspan\u003e \u003c\/span\u003etwist nozzle to make sure it is secure in quick-release socket.\u003c\/b\u003e\u003cbr\u003eRisk of injury. Ensure nozzle is completely inserted in quick-release socket before turning on gun trigger.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003c\/ol\u003e\n\u003ch2\u003eCONNECTION TO ELECTRICAL SUPPLY\u003c\/h2\u003e\n\u003col\u003e\n\u003cli\u003eMake sure that the mains voltage is the same as shown on the identification label on the identification label on the machine.\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003e\u003cb\u003eWARNING\u003c\/b\u003e\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eMake sure that the plug complies with your local regulations, and it is provided with ground connection (earth)\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003e\u003cb\u003eWARNING\u003c\/b\u003e\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eThe power outlet must be protected by a residual circuit breaker with a sensitivity of less than 30mA.\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003e\u003cb\u003eWARNING\u003c\/b\u003e\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eDo not connect other appliances to the same outlet.\u003c\/li\u003e\n\u003cli\u003e\n\u003cspan\u003e\u003cb\u003eWARNING\u003c\/b\u003e\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003eInsert the plug after checking the switch joint the machine in the OFF position.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e \u003c\/p\u003e\n\u003ch2\u003eSTARTING THE MACHINE\u003c\/h2\u003e\n\u003cp\u003e\u003cspan\u003e\u003cb\u003eWARNING\u003c\/b\u003e\u003c\/span\u003e\u003cspan\u003e In case of power failure, turn the unit OFF for safety reasons.\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eSupply water to the machine, then press the gun trigger\u003c\/li\u003e\n\u003cli\u003eSwitch on the unit.\u003c\/li\u003e\n\u003cli\u003eHold the gun in the open position for a few seconds to drain the air from the hose.\u003c\/li\u003e\n\u003cli\u003eAt this stage, adjust the machine pressure to your pressure requirement and you are ready to enjoy your work.\u003c\/li\u003e\n\u003cli\u003eDuring washing, it is better not to exceed the recommended pressure.\u003c\/li\u003e\n\u003cli\u003eDuring washing, the spray head should not be far away from the dirty surface.\u003cbr\u003e\u003cspan\u003e\u003cb\u003eWARNING\u003c\/b\u003e\u003c\/span\u003e\u003cspan\u003e \u003c\/span\u003e\u003cb\u003eDo not use the machine when people or animals are in range of the jet.\u003c\/b\u003e\u003cbr\u003eStop the gun after ending the washing, then switch the engine off. Do not let the unit run with the gun switched off for more than 2 minutes. The unloading valve is still moving agter stopping the gun, the water will flow in circle in the pump, which will make the water hot and damage the seal ring, ceramics or other accessories if the machine is kept running.\u003c\/li\u003e\n\u003cli\u003eDuring the operation, it is normal if there is a little water leaks out from the pump, which will not effect the use of the machine.\u003c\/li\u003e\n\u003cli\u003eSAFETY VALVE: The safety valve also functions as a pressure limiting valve. When the gun trigger is released, the safety valve opens and the water recirculate through the pump inlet.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch2\u003eSTOPPING THE MACHINE\u003c\/h2\u003e\n\u003col\u003e\n\u003cli\u003eWhen not in use, switch the machine off.\u003c\/li\u003e\n\u003cli\u003eHold the gun in the open position for a few seconds to drain water from the hose.\u003c\/li\u003e\n\u003c\/ol\u003e\n\u003cp\u003e\u003cspan\u003e\u003cb\u003eWARNING\u003c\/b\u003e\u003c\/span\u003e\u003cspan\u003eHigh pressure water jets are potentially dangerous is used incorrectly. In particular, DO NOT direct the water jet towards people or animals, electrical equipment or the unit itself.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch1\u003eAPPLICATION FIELD\u003c\/h1\u003e\n\u003cul\u003e\n\u003cli\u003eTo maintain and wash the deversified vehicles, project machinery, architecture and agricultural machinery.\u003c\/li\u003e\n\u003cli\u003eTo maintain and wash the army vehicles, tanks, naval vesssels, planes, and other military machinery.\u003c\/li\u003e\n\u003cli\u003eWash and disinfect the diver sited harbour containers.\u003c\/li\u003e\n\u003cli\u003eWash sanitation recovery and disinfection at stock farm, breeding house and slaughterhouse.\u003c\/li\u003e\n\u003cli\u003eDaily wash of buildings glass and the outside walls.\u003c\/li\u003e\n\u003cli\u003eWash and disinfect the enviroment of townsfolk square, carnie, hospitals, hotels, restaurants and the courtyard.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch1\u003ePUMP OPERATING FEATURES\u003c\/h1\u003e\n\u003cul\u003e\n\u003cli\u003eThe level of the oil must be checked periodically.\u003c\/li\u003e\n\u003cli\u003eIt is most important that the oil is changed after the first 50 hours of work and successively every 100 hous.\u003c\/li\u003e\n\u003cli\u003eIn any case we suggest to change the oil at least once a year.\u003c\/li\u003e\n\u003cli\u003e\u003cb\u003eOIL TYPE: SAE 15W-40 or equivalent motor oil.\u003c\/b\u003e\u003c\/li\u003e\n\u003cli\u003e\n\u003cb\u003eHow to change pump oil:\u003c\/b\u003e\u003cbr\u003eDrain the old pump il completely through the oil outlet plug.\u003cbr\u003eInstall the oil outlet plug again and pour the clean oil in the crankcase, the oil level should be slightly over the center line of the oil mirror.\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003ch1\u003eTROUBLE SHOOTING\u003c\/h1\u003e\n\u003ch3\u003eFOR QUALIFIED PERSONNEL ONLY\u003c\/h3\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003ePump running normally but pressure does not achieve rated values.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePump sucking air\u003c\/li\u003e\n\u003cli\u003eValve worn or dirty\u003c\/li\u003e\n\u003cli\u003eWorn Out Unloader valve\u003c\/li\u003e\n\u003cli\u003eWorn out piston seals\u003c\/li\u003e\n\u003cli\u003eDirty filter\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck that hoses and fittings are air tight\u003c\/li\u003e\n\u003cli\u003eCheck, clean and replace\u003c\/li\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003eFluctuating pressure\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eValves worn, dirty or stuck\u003c\/li\u003e\n\u003cli\u003ePump sucking air\u003c\/li\u003e\n\u003cli\u003eDamaged or dirty Check Valves\u003c\/li\u003e\n\u003cli\u003eDirty filter\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003cli\u003eCheck that hoses and fittings are air tight\u003c\/li\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003cli\u003eCheck and clean\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003ePressure drops after period of normal use.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eWorn Nozzle\u003c\/li\u003e\n\u003cli\u003eCheck Valve is worn, dirty or stuck\u003c\/li\u003e\n\u003cli\u003eWorn Out Unloader valve\u003c\/li\u003e\n\u003cli\u003eWorn out piston seals\u003c\/li\u003e\n\u003cli\u003eDirty filter\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003cli\u003eCheck, clean and replace\u003c\/li\u003e\n\u003cli\u003eCheck, clean and replace\u003c\/li\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003cli\u003eCheck and clean\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003ePump is noisy.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePump sucking air\u003c\/li\u003e\n\u003cli\u003eValve worn, dirty or stuck\u003c\/li\u003e\n\u003cli\u003eWorn Out bearings\u003c\/li\u003e\n\u003cli\u003eWater Top hot\u003c\/li\u003e\n\u003cli\u003eDirty filter\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck that hoses and fittings are air tight\u003c\/li\u003e\n\u003cli\u003eCheck, clean and replace\u003c\/li\u003e\n\u003cli\u003eCheck and replace if necessary\u003c\/li\u003e\n\u003cli\u003eReduce Temperature\u003c\/li\u003e\n\u003cli\u003eCheck and clean\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003eWater in oil.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eHigh humidity in air\u003c\/li\u003e\n\u003cli\u003ePiston seal or oil seal worn out\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck and change oil twice as often\u003c\/li\u003e\n\u003cli\u003eCheck and replace\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003eWater dripping from under the pump.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003ePiston seals damaged or worn out\u003c\/li\u003e\n\u003cli\u003eThe O-ring of piston guide or retainer worn\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck and Replace\u003c\/li\u003e\n\u003cli\u003eCheck and Replace\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003eOil leaking.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eOil seal worn out\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck and Replace\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003eThe motor does not start when switched on.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe plug not well connected or lack of power supply\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck plug, cable and switch\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003eWhen switching the unit on, the motor turns but does not run.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eThe mains voltage is insufficient, lower than the minimum requirement\u003c\/li\u003e\n\u003cli\u003eThe pump is stuck or frozen\u003c\/li\u003e\n\u003cli\u003eIncorrect extension cable\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck that the main power supply is adequate\u003c\/li\u003e\n\u003cli\u003eFollow the correct precautions\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eFault:\u003c\/b\u003e\u003cspan\u003eThe motor stops running.\u003c\/span\u003e\u003cbr\u003e\u003cb\u003eCause:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eTripped internal overload due to overheating\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cb\u003eSolution:\u003c\/b\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003eCheck that the main voltage corresponds to the specifications\u003c\/li\u003e\n\u003cli\u003eWait a few minutes before turning on the unit again\u003c\/li\u003e\n\u003c\/ul\u003e","brand":"Scrubio Cleaning","offers":[{"title":"Default Title","offer_id":52725018558737,"sku":null,"price":13999.0,"currency_code":"ZAR","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0949\/2358\/7857\/files\/4_f2ff9b13-75c1-4101-9cbe-a57c26dba2ac.png?v=1763084259","url":"https:\/\/scrubiocleaning.com\/products\/pressure-washer-14l-min-2500-psi-380v-4kw","provider":"Scrubio Cleaning","version":"1.0","type":"link"}